Sponsored Content
Operating Systems Solaris fork: Resource temporarily unavailable - What can I check ? Post 302114096 by reborg on Thursday 12th of April 2007 01:11:14 PM
Old 04-12-2007
Quote:
Originally Posted by Perderabo
And it is possible for a large process to be unable to fork while smaller processes have no problem.
Quite right of course and as an extension, some bigger process might die because it runs out of memory, leaving enough room for applications with a smaller memory footprint to run quite happily.

Both of the suggestion I posted were to run prior to the problem happening. The cron to give a general idea of what was happening, or more simply to periodically run the commands before the problem happened which might in fact point out the exact cause before the problem happened for example some application or script writing a huge log file to /tmp.

Last edited by reborg; 04-12-2007 at 07:17 PM..
 

10 More Discussions You Might Find Interesting

1. Solaris

sendto failing "resource temporarily unavailable"

Well, I am not even sure if its failing, cause at the other end I have a select call and it wakes up and reads the data I sent fine. Ok here is the issue, I have a UDP socket(non blocking) through which I push some data to another port. At the other end I have select loop, waiting for this data.... (6 Replies)
Discussion started by: Naanu
6 Replies

2. UNIX for Advanced & Expert Users

Fork:resource unavailable

Hello. I have code which create processes with fork(). I set a limit for processes by typing ulimit -u 20. Then I run my code who should create 100 processes. Unfortunately, I have a mistake there and I forgot to quit all of my forked processes when fork gave me return value -1. So I am trapped in... (5 Replies)
Discussion started by: samos
5 Replies

3. Solaris

Mmap with fork : Resource unavaialable temporarily

installed 64bit 16GB VM on 64bit ESX server. Written small C code to map the 2GB of memory by mmap after creating 3 child and map getting failed by throwing "resource unavailable temporarily" after mapping 1.6 GB of memory out of 2GB. But same 1.5Gb memory mapping works fine. I checked... (0 Replies)
Discussion started by: siddharoodh
0 Replies

4. UNIX for Dummies Questions & Answers

Resource temporarily unavailable Error In Socket

Hi, Now I am programming to communicate with some network printer through TCP Socket program.By sending command "\033E 1\r" to printer,causes, check the port for error normally. In my case i used following code bytesSent = send( sockfd, "\033E 1\r",sizeof("\033E 1\r"), 0); ... (1 Reply)
Discussion started by: kavinsivakumar
1 Replies

5. Red Hat

cannot set user id: Resource temporarily unavailable (not open file/open process related)

First post, sorry to be a bother but this one has been dogging me. I have a process user (java application server) that trips a resource limit every couple weeks and need help finding what limit we're hitting. First, this is what's running: This is the error when jobs are run or the... (0 Replies)
Discussion started by: Katahdin
0 Replies

6. UNIX for Advanced & Expert Users

fork: Resource temporarily unavailable , server unexpectedly unavailable network connection

Solaris 10 Server refuse to connect :wall: fork: Resource temporarily unavailable , server unexpectedly unavailable network connection , refuse error, disconnect message, fatal error type2, (protocol error type2) Issue has been resolved after taken few steps :b: First of all need to check... (1 Reply)
Discussion started by: taherahmed
1 Replies

7. UNIX for Dummies Questions & Answers

Fork: Resource Temporarily Unavailable

I wrote a script that works most of the time but gave me fork: resource temporarily unavailable some of the time. I restarted my computer and now it runs fine but googling "fork: resource temporarily unavailable" and looking on the forums has not actually helped me figure out what exactly I... (3 Replies)
Discussion started by: monstrousturtle
3 Replies

8. Programming

[ERROR:Resource temporarily unavailable!] Serial writing by termios library

Hello, I am using the termios library to write data that I get from a Bluetooth device to a modem via serial. The data arrive from the Bluetooth device correctly every 50ms and I have to bypass them on the serial ttyUSB3 where it is connected to a modem connected to a socket with static IP. The... (10 Replies)
Discussion started by: enaud
10 Replies

9. UNIX for Dummies Questions & Answers

Fork resource unavailable error, max # filehandles open?

I wrote a perl program that simultaneously reads in data from 691 tar.gz files using zcat. I can run one instance of the program without any issues and the memory and swap sizes are negligible. However, when I attempt to run more than 1 I start to get fork: resource unavailable messages. Are... (6 Replies)
Discussion started by: aquinom85
6 Replies

10. Shell Programming and Scripting

Fork: Resource temporarily unavailable

Hi friends, Working on a linux X86-64 bit system, I suddenly started getting this error (mentioned in subject) from various scripts. I googled, found that there are couple of reason which causes this issue. - less memory I am pretty sure, memory seems to be stable on my system and at the... (15 Replies)
Discussion started by: clx
15 Replies
LIBBASH(7)							  libbash Manual							LIBBASH(7)

NAME
libbash -- A bash shared libraries package. DESCRIPTION
libbash is a package that enables bash dynamic-like shared libraries. Actually its a tool for managing bash scripts whose functions you may want to load and use in scripts of your own. It contains a 'dynamic loader' for the shared libraries ( ldbash(1)), a configuration tool (ldbashconfig(8)), and some libraries. Using ldbash(1) you are able to load loadable bash libraries, such as getopts(1) and hashstash(1). A bash shared library that can be loaded using ldbash(1) must answer 4 requirments: 1. It must be installed in $LIBBASH_PREFIX/lib/bash (default is /usr/lib/bash). 2. It must contain a line that begins with '#EXPORT='. That line will contain (after the '=') a list of functions that the library exports. I.e. all the function that will be usable after loading that library will be listed in that line. 3. It must contain a line that begins with '#REQUIRE='. That line will contain (after the '=') a list of bash libraries that are required for our library. I.e. every bash library that is in use in our bash library must be listed there. 4. The library must be listed (For more information, see ldbashconfig(8)). Basic guidelines for writing library of your own: 1. Be aware, that your library will be actually sourced. So, basically, it should contain (i.e define) only functions. 2. Try to declare all variables intended for internal use as local. 3. Global variables and functions that are intended for internal use (i.e are not defined in '#EXPORT=') should begin with: __<library_name>_ For example, internal function myfoosort of hashstash library should be named as __hashstash_myfoosort This helps to avoid conflicts in global name space when using libraries that come from different vendors. 4. See html manual for full version of this guide. AUTHORS
Hai Zaar <haizaar@haizaar.com> Gil Ran <ril@ran4.net> SEE ALSO
ldbash(1), ldbashconfig(8), getopts(1), hashstash(1) colors(1) messages(1) urlcoding(1) locks(1) Linux Epoch Linux
All times are GMT -4. The time now is 11:38 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy