01-04-2007
Tornado, grial:
Thanks so much for your advice. I have followed your instruction to test as:
/etc/rc2.d/S99dbora, returning message is: Oracle startup: cnanot start. Then I linked dbora to rc3.d as S99dbora and tested as /etc/rc3.d/S99dbora. I got the same message: Oracle startup: cannot start. Then I checked user to run the script. Since I created dbora as root user, etc - run by sys, rc2 - root, rc2.d - sys, rc3 -root, rc3.d - sys, S99dbora - root under rc2.d or rc3.d. These settings were generated by installation. Should I chown S99dbora to be run by oracle or group user dba? Thanks.
8 More Discussions You Might Find Interesting
1. Cybersecurity
Our systems group is asking if it would be Ok to turn off certain services due to potention security risks. The following are being contemplated.
Service
chargen
daytime
discard
dtspcd
echo
exec
finger
fs
gssd
in.comsat
kcms_server
ktkt_warnd
login
name
rpc.cmsd
rpc.metad... (4 Replies)
Discussion started by: BCarlson
4 Replies
2. UNIX for Advanced & Expert Users
dear all,
i have 2 questions on solaris 10. I noticed telnet/ftp/print services suddenly being stopped on one server. How can i trace this issue and find a resolution. Other issue is i need to enable rsh within the same host. enabled the service rexec and have created the .rhosts and have a + in... (4 Replies)
Discussion started by: earlysame55
4 Replies
3. Solaris
I've installed Solaris 10 (05-08) on a SPARC platform
During the installation I was prompted with the question below. I selected yes to enable remote services.
Does anyone know what services this option enables?
- Enabling remote services ----------------------------------------
Would... (6 Replies)
Discussion started by: soliberus
6 Replies
4. Solaris
We need a DNS Server on DNS 10. What the best product can i buy and install ?
Help me, pls.
Tks all. (1 Reply)
Discussion started by: quan0509
1 Replies
5. Solaris
Hello
We have recently been through an audit of our solaris servers.
All our solaris servers are running version 10.
We have been told to close down all the services and we have closed what we could by using svcadm disable
We only wish to let ssh and the ftp service to run.
Below is a... (3 Replies)
Discussion started by: sollyshah
3 Replies
6. Solaris
I'm looking for help with a legacy system.
I have some obsolete equipment connected to an Ultra 60 running Solaris 5.7 with the binary for a 32 bit driver. The driver is rejected by newer versions of solaris, which run 64 bit kernels.
I hope to reverse engineer the driver so that I can... (0 Replies)
Discussion started by: obsoleteStuff
0 Replies
7. Solaris
Scenario: I have installed a service. When I start it by running /etc/init.d/<service> start it generates a massive amount of audit data (auditd) in /var/audit. So much so that running the service for any length of time is inadvisable due to overhead.
However if I reboot the system the... (6 Replies)
Discussion started by: penguinpanzer
6 Replies
8. Solaris
Hi,
Few services not starting on new build Solaris 11 non-global zone. I uninstalled zone and reinstalled and still same issue, while global zone is working fine.
smpt service is going into maintenance mode and /var/svc/log/network-smtp:sendmail.log shows that it tries and then dead
... (0 Replies)
Discussion started by: solaris_1977
0 Replies
rc0(8) System Manager's Manual rc0(8)
NAME
rc0 - Runs command script executed when stopping the system
SYNOPSIS
rc0
DESCRIPTION
The rc0 script contains run commands that enable a smooth shutdown and bring the system to a single-user state; run levels 0 and s. In
addition to commands listed in within the script itself, rc0 contains instructions to run commands found in the /sbin/rc0.d directory. The
script defines the conditions under which the commands execute; some commands run if the system is being shut down while others run if the
system is being shut down and rebooted to single user.
By convention, files in the /sbin/rc0.d directory begin with either the letter "K" or the letter "S" and are followed by a two-digit number
and a filename, for example: K00enlogin K05lpd K60cron K30nfs
In general, the system starts commands that begin with the letter "S" and stops commands that begin with the letter "K." The numbering of
commands in the /sbin/rc0.d directory is important since the numbers are sorted and the commands are run in ascending order. Files in the
/sbin/rc0.d directory are normally links to files in the /etc/init.d directory.
An entry in the inittab file causes the system to execute the rc0 script, for example: ss:Ss:wait:/sbin/rc0 shutdown < /dev/console >
/dev/console 2>&1 s0:0:wait:/sbin/rc0 off < /dev/console > /dev/console 2>&1
The following operations are typical of those that result from executing the rc0 script and the commands located in the /sbin/rc0.d direc-
tory: Notify users that the system is shutting down. Sync the disks Stop system services and daemons Stop processes Kill processes Unmount
file systems Invoke init if the system is being shut down to single user
The killall command sends a SIGTERM signal to stop running processes; SIGKILL follows to kill all processes except the process which initi-
ated the call. The umount -a command unmounts all file systems except the root file system.
FILES
Specifies the command path Specifies the directory of commands that corresponds to the run level
RELATED INFORMATION
Commands: init(8), killall(8), rc2(8), rc3(8), shutdown(8) delim off
rc0(8)